• Products

    Dynamic Speakers

    BMR Speakers

    Dynamic Receivers

    Balanced Armature Receivers

    Buzzers

    Audio Exciters

    Boom Microphones & Sensors

    ECM Microphones

    MEMS Microphones

    Specialty Microphones

    IA Microphones

    Accelerometers

    Voice Vibration Sensors

    Acoustic Dampers

    Wax Protection

    Telecoils

    Programming Accessories

    Speaker Modules

    Microphone Modules

    RIC Modules

    ProxFusion Multi-Sensors

    ProxFusion Evaluation Kits

    ProxSense Capacitive Sensors

    ProxSense Modules

    ProxSense Evaluation Kits

    Neural Decision Processors

    DSP for Hearing Aids

    DSP for Hearing Aids Evaluation Kit

    Bluetooth Modules

    Bluetooth Modules Evaluation Kit

  • Acoustic Design Service

    Speaker Solutions

    Microphone Solutions

    Over the ear & In-ear Solutions

    Measurement Capabilities

    Electroacoustic Simulations

  • Engineering & Manufacturing

    Speaker Modules

    Microphone Modules

    Industrial Tools

  • Partners
  • About us
  • News
    • Acoustic Reviews
    • Events
    • Webinars
Contact Us
  • Products

    Dynamic Speakers

    BMR Speakers

    Dynamic Receivers

    Balanced Armature Receivers

    Buzzers

    Audio Exciters

    Boom Microphones & Sensors

    ECM Microphones

    MEMS Microphones

    Specialty Microphones

    IA Microphones

    Accelerometers

    Voice Vibration Sensors

    Acoustic Dampers

    Wax Protection

    Telecoils

    Programming Accessories

    Speaker Modules

    Microphone Modules

    RIC Modules

    ProxFusion Multi-Sensors

    ProxFusion Evaluation Kits

    ProxSense Capacitive Sensors

    ProxSense Modules

    ProxSense Evaluation Kits

    Neural Decision Processors

    DSP for Hearing Aids

    DSP for Hearing Aids Evaluation Kit

    Bluetooth Modules

    Bluetooth Modules Evaluation Kit

  • Acoustic Design Service

    Speaker Solutions

    Microphone Solutions

    Over the ear & In-ear Solutions

    Measurement Capabilities

    Electroacoustic Simulations

  • Engineering & Manufacturing

    Speaker Modules

    Microphone Modules

    Industrial Tools

  • Partners
  • About us
  • News
    • Acoustic Reviews
    • Events
    • Webinars
Contact Us
  • Products
  • Acoustic Design Service
  • Engineering & Manufacturing
  • Partners
  • About us
  • News
    • Acoustic Reviews
    • Events
    • Webinars
Menu
  • Products
  • Acoustic Design Service
  • Engineering & Manufacturing
  • Partners
  • About us
  • News
    • Acoustic Reviews
    • Events
    • Webinars
Contact Us
Home / Acoustic Review / Electrodynamic Loudspeaker – the Lumped Element Modeling approach

Electrodynamic Loudspeaker – the Lumped Element Modeling approach

Since its invention by C. Rice and E. Kellogg in 1925 [1], the electrodynamic loudspeaker has been more than widely exploited in the audio industry. But if we come to discuss the means of predicting its acoustic behavior, it is rather when L. Beranek published his book Acoustics in 1954 [2][3] that the first models (based on the principle of Lumped elements [4]) were popularized. Among the electroacoustic parameters listed by Beranek in his book (also formulated by A. Thiele and R. Small at the same era), here are the fundamental ones:

       – 𝑅𝑒, the electrical resistive part of the voice coil, in ohms,

       – 𝐿𝑒, the electrical inductive part of the voice coil, in millihenries (often at 1k Hz),

       – B.l, the product of magnet field strength in the voice coil gap and the length of wire in the magnetic field, in tesla-meters,

       – 𝑀𝑀𝑆, the mass of the assembly “diaphragm / voice coil”, the mass of half of the outer suspension and the mass of air particles around the diaphragm (that becomes non-negligeable when dealing with small sized speakers), in kilograms,

       – 𝑅𝑀𝑆, the mechanical resistance of suspensions, in Newton-second per meters,

       – 𝐶𝑀𝑆, the total mechanical compliance of suspensions, in meter per Newton,

       – 𝑆𝐷 (mentioned in the form of the radius “a” in the Beranek’s book), the projected area of the speaker diaphragm.

In his book, Beranek also helped popularize the electrical network that defines the electro-mechano-acoustic behavior of such a loudspeaker. The diagrams in Figure 1 present three loops, dealing respectively with the electrical, mechanical, and acoustic domain of the transducer.

Among important analogies brought by this circuit, ones to save in mind are:

       – Voltage (U) from the first loop becomes a mechanical force (F) in the second loop and an acoustical pressure (P) in the third loop,

       – Current (i) from the first loop becomes a mechanical velocity (v) in the second loop and an acoustical flow (q) in the third loop.

Figure 1 – Lumped element circuit of a dynamic loudspeaker

In this circuit, the link between the loop No. 1 and 2 is ensured by a gyrator. This later defines the following relationship F = B.l * i ; U = B.l * v  . The link between the loop No. 2 and 3 is achieved through a transformer. This later defines the following relationship P = F/SD

It is important to note that this modeling approach assumes one-dimensional acoustic behavior only. There is therefore an upper frequency limit for the validity of this model, which we can approximate as its quarter wavelength being comparable to the size of the diaphragm of the loudspeaker considered.

The Figure 2 below illustrates an example around a 45 mm dia. loudspeaker, where measurements are compared to simulations. From this comparison, we observe a very good matching of the predictions until the theoretical frequency limit of 1.9 – 2k Hz. Above this frequency, radiation from the loudspeaker slowly starts to be impacted by the resonances from the diaphragm itself.

Figure 2 – Measurement (Solid line) vs Lumped element model (dashed line)

By adding a few components to the model presented in Figure 1, it then becomes possible to simulate the impact of a rear volume or a front cavity on the speaker sound signature.

Seltech can help you simulate your system and refine each parameter to offer you an acoustic solution that precisely meets your requirements.

Discover more about our acoustic department

Review by:

Frédéric Fallais, Acoustic Application Engineer

Arthur Di Ruzza, Acoustic Technician

Sources :

[1] C. W. Rice and E. W. Kellogg, “Notes on the Development of a New Type of Hornless Loud Speaker,” Transactions A.I.E.E., 1925, Vol. XLIV

[2] L. L. Beranek, Acoustics, Massachusetts: Institute of Technology, 1954

[3] L. L. Beranek and T. Mellow, Acoustics: Sound fields, Transducers and Vibration (Second Edition), Academic Press, 2019

[4] https://en.wikipedia.org/wiki/Lumped-element_model

[Fig.1] J. Hipperson et al. Multiphysics simulation of a low frequency horn loudspeaker, Institute of Acoustics, Reproduced Sound 2021

Facebook
Twitter
LinkedIn
Pinterest
PrevPreviousVibrational haptics – Mechanics behind touch sensation
NextExploring two-dimensional planar arraysNext

Headquarters
SAS SELTECH
2, Allée des Cerisiers
F – 94042 Créteil FRANCE
Tel EU : +33 1 48 92 90 02
Tel NA : +1 (919) 481 6896

Products

  • Acoustic Components
  • Capacitive, Multifunctional Sensors
  • Processors
  • Wireless Systems
  • Acoustic Components
  • Capacitive, Multifunctional Sensors
  • Processors
  • Wireless Systems

Services

  • Acoustic Design Service
  • Engineering & Manufacturing
  • Acoustic Design Service
  • Engineering & Manufacturing

Legal

  • Terms & Conditions EU
  • Terms & Conditions US
  • Corporate Social Responsability
  • Legal Notices
  • Terms & Conditions EU
  • Terms & Conditions US
  • Corporate Social Responsability
  • Legal Notices

© Copyright 2025 SELTECH, All Right Reserved.